Cirrus 3CFM Provozní pokyny stáhnout pdf (Strana 7)

Page 7

TIPS FROM THE PROS

YOUR XST 4WD TRUGGY RTR SHOULD INCLUDE THE FOLLOWING ITEMS SEPARATELY IN THE BOX:

Tyres and Wheels (Glued)

Body Clips

Decal Set

Plastic Parts Set

Receiver Antenna Support Tube

Suspension Plate Holders

Air lter Assembly

Allen Keys and Wrenches

PREPARING TO RUN YOUR XST 4WD TRUGGY RTR

Now that you are familiar with the major component parts of your XST 4WD Truggy RTR, and with the functions of the Cirrus 3CFM

transmitter, it's time to prepare your XST 4WD Truggy RTR for its rst run.

IMPORTANT: Before continuing, please double-check that you've read and understood the warnings on page 2. It's important that

you understand this information before preparing to run your XST 4WD Truggy RTR. Also, remember, if you have any questions or

encounter any problems, you can contact your local distributor using the Customer Service Information on page 3.

XST 4WD Truggy RTR Chassis

Cirrus 3CFM 3 Channel FM Transmitter

Transmitter Antenna

Lexan Body Shell (Printed) and Nylon Wing

STEP 1: FINAL ASSEMBLY

Make sure to read these Operating Instructions and Assembly Manual in its entirety before starting. This will allow you to become

familiar with the XTM Racing XST 4WD Truggy RTR, XTM Racing 24.7 Nitro Engine and Cirrus 3CFM radio control system.

Double-check all of the fasteners to ensure that they're tight.

Any screws that are threaded directly into metal should be secured into place with threadlock. This will prevent the screws from loosening

during use. Screws threaded into nylon or composite material do not require threadlock.

Do not overtighten any screws that thread into nylon or composite material, or the material may strip out. Screws threaded into nylon

or composite material need only be tightened snugly.

After installing the receiver batteries into the battery holder, t a rubber band or a nylon cable tie around the battery holder. This will

prevent the batteries from coming loose when doing jumps, etc.

If you have difculty sliding the receiver antenna wire through the antenna support tube, rst pull the antenna wire through your ngers

several times to straighten it, then lightly wet the antenna wire with glass cleaner. The glass cleaner will make the antenna wire slide

through the support tube much easier.

When testing the steering, lift the front of the XST 4WD Truggy RTR off the ground. This will allow the steering system to operate

smoothly, without any binding.

If the carburettor barrel does not open completely when you pull the throttle trigger, adjust the throttle trim on the transmitter until the

carburettor barrel opens completely when you pull back fully on the throttle trigger.

When oiling the air lter element, place the cleaned air lter element in a plastic bag and then apply the air lter oil on it. Close the bag

and work the oil into the air lter element. This allows you to work the oil into the element without getting excess oil on your hands.

When you pinch the fuel line to stop the engine, you must pinch it hard and hold it. The engine will rev up quickly, then stop. We

suggest holding the XST 4WD Truggy RTR while doing this, so that it doesn't lurch out of your hands.

Other than during the break-in period, always make sure that you install the body when driving your XST 4WD Truggy RTR. When

your XST 4WD Truggy RTR ips over, the body will help protect the chassis and its components.

Place the chassis on a dedicated car stand or similar so that all four wheels are suspended off the ground. This ensures that your

XST 4WD Truggy RTR does not accidentally drive away when starting the engine if the idle setting is too high.

q Install the wheels onto the chassis, making sure to tighten the wheel retaining nuts

rmly, using a 17mm wrench.

Notice that the back of the wheels are moulded to key over the hex-shaped wheel

hubs. All four wheels and tyres are the same size.

IMPORTANT: Double-check that the tyres are glued onto the wheels. If they're not,

glue the tyres onto the wheels, using C/A tyre glue. See page 51 for information on

how to glue the tyres onto the wheels.

1 2 3 4 5 6 7 8 9 10 11 12 ... 63 64

Komentáře k této Příručce

Žádné komentáře

Cirrus 3CFM Provozní pokyny Strana 7

Komentáře k této Příručce